## WebSocket How-To

### Table of Contents

- Overview
- Application development
- Production usage
- Tomcat WebSocket specific configuration

### Overview

Tomcat provides support for WebSocket as defined by RFC 6455.

### Application development

Tomcat implements the Java WebSocket 1.1 API defined by JSR-356.

There are several example applications that demonstrate how the WebSocket API can be used. You will need to look at both the client side HTML and the server side code.

### Production usage

Although the WebSocket implementation does work with any of the HTTP connectors, it is not recommended to the WebSocket with the BIO HTTP connector as the typical uses of WebSocket (large numbers of mostly idle connections) is not a good fit for the HTTP BIO connector which requires that one thread is allocated per connection regardless of whether or not the connection is idle.

It has been reported (56304) that Linux can take large numbers of minutes to report dropped connections. When using WebSocket with the BIO HTTP connector this can result in threads blocking on writes for this period. This is likely to be undesirable. The time taken for the connection to be reported as dropped can be reduced by using the kernel network parameter `/proc/sys/net/ipv4/tcp_retries2`. Alternatively, one of the other HTTP connectors may be used as they utilise non-blocking IO enabling Tomcat to implement its own timeout mechanism to handle these cases.

### Tomcat WebSocket specific configuration

Tomcat provides a number of Tomcat specific configuration options for WebSocket. It is anticipated that these will be absorbed into the WebSocket specification over time.

The write timeout used when sending WebSocket messages in blocking mode defaults to 20000 milliseconds (20 seconds). This may be changed by setting the property `org.apache.tomcat.websocket.BLOCKING_SEND_TIMEOUT` in the user properties collection attached to the WebSocket session. The value assigned to this property should be a `Long` and represents the timeout to use in milliseconds. For an infinite timeout, use `-1`.

If the application does not define a `MessageHandler.Partial` for incoming binary messages, any incoming binary messages must be buffered so the entire message can be delivered in a single call to the registered `MessageHandler.Whole` for binary messages. The default buffer size for binary messages is 8192 bytes. This may be changed for a web application by setting the servlet context initialization parameter `org.apache.tomcat.websocket.binaryBufferSize` to the desired value in bytes.

If the application does not define a `MessageHandler.Partial` for incoming text messages, any incoming text messages must be buffered so the entire message can be delivered in a single call to the registered `MessageHandler.Whole` for text messages. The default buffer size for text messages is 8192 bytes. This may be changed for a web application by setting the servlet context initialization parameter `org.apache.tomcat.websocket.textBufferSize` to the desired value in bytes.

The Java WebSocket specification 1.0 does not permit programmatic deployment after the first endpoint has started a WebSocket handshake. By default, Tomcat continues to permit additional programmatic deployment. This behavior is controlled by the `org.apache.tomcat.websocket.noAddAfterHandshake` servlet context initialization parameter. The default may be changed by setting the `org.apache.tomcat.websocket.STRICT_SPEC_COMPLIANCE` system property to `true` but any explicit setting on the servlet context will always take priority.

The Java WebSocket 1.0 specification requires that callbacks for asynchronous writes are performed on a different thread to the thread that initiated the write. Since the container thread pool is not exposed via the Servlet API, the WebSocket implementation has to provide its own thread pool. This thread pool is controlled by the following servlet context initialization parameters:

- `org.apache.tomcat.websocket.executorCoreSize`: The core size of the executor thread pool. If not set, the default of 0 (zero) is used. Note that the maximum permitted size of the executor thread pool is hard coded to `Integer.MAX_VALUE` which effectively means it is unlimited.
- `org.apache.tomcat.websocket.executorKeepAliveTimeSeconds`: The maximum time an idle thread will remain in the executor thread pool until it is terminated. If not specified, the default of 60 seconds is used.

When using the WebSocket client to connect to server endpoints, the timeout for IO operations while establishing the connection is controlled by the `userProperties` of the provided `javax.websocket.ClientEndpointConfig`. The property is `org.apache.tomcat.websocket.IO_TIMEOUT_MS` and is the timeout as a `String` in milliseconds. The default is 5000 (5 seconds).

When using the WebSocket client to connect to secure server endpoints, the client SSL configuration is controlled by the `userProperties` of the provided `javax.websocket.ClientEndpointConfig`. The following user properties are supported:

- `org.apache.tomcat.websocket.SSL_CONTEXT`
- `org.apache.tomcat.websocket.SSL_PROTOCOLS`
- `org.apache.tomcat.websocket.SSL_TRUSTSTORE`
- `org.apache.tomcat.websocket.SSL_TRUSTSTORE_PWD`

The default truststore password is `changeit`.

If the `org.apache.tomcat.websocket.SSL_CONTEXT` property is set then the `org.apache.tomcat.websocket.SSL_TRUSTSTORE` and `org.apache.tomcat.websocket.SSL_TRUSTSTORE_PWD` properties will be ignored.

### Comments

Notice: This comments section collects your suggestions on improving documentation for Apache Tomcat.
If you have trouble and need help, read Find Help page and ask your question on the tomcat-users mailing list. Do not ask such questions here. This is not a Q&A section.
The Apache Comments System is explained here. Comments may be removed by our moderators if they are either implemented or considered invalid/off-topic.